Tip 1: How to fix the corrugation for the toilet

Tip 1: How to fix the corrugation for the toilet



Installation Toilet bowl Own strength is considered responsible andlaborious process. But do not be afraid. You can, of course, hire specialists and trust them with a replacement, but this service has a fairly high cost. It is best to do the work yourself.





How to install a corrugated toilet bowl


















Instructions





1


In order not to encounter many problems, it is necessary to study the old toilet bowl in advance, as well as the technology of its installation. Be sure to pay attention to the angle of release Toilet bowl and its height from the floor. The angle can be straight, oblique or to the floor. If the data of your new model do not coincide with the data of the old one, it is necessary to purchase a drain corrugation. Read the water supply system well. Most often there is a lateral or lower threading on a flexible hose. Sometimes you can also meet a metal pipe. When choosing Toilet bowl consider the length of the future supply of water to the tank. It is recommended to buy a new flexible water supply in advance. Find out if it is possible to cut off cold water in the tap for tapping the tank. If this can not be done, then contact the plumber on duty. They will help replace the input faucets.





2


Now you can proceed to work. First you need to drain the water from the barrel Toilet bowl And detach the water supply. If there is a flexible liner, then it must be unscrewed from the barrel and from the water supply. It can easily be removed. If the piping is metal, you need to cut out a part of the pipe, and on the water pipe side, disassemble the threaded connections before the first "dad" connection. Then you will be able to tighten the nut of the flexible liner.





3


Change the toilet is not so difficult. First, the bolts are unscrewed, and the cement is broken at the fastening points. During the removal Toilet bowl It is necessary to drain the water that is available in its internal cavities. To do this, simply tilt it back.





4


You can connect a new toilet bowl to the sewer withUsing corrugation. To install it in the sewer pipe, it is necessary to lubricate the sealant from the inlet to the sewer. Similar actions are performed with the funnel. The corrugation must be inserted as far as it will go. The most difficult thing is to install a toilet with an oblique and straight outlet.




























Tip 2: How to remove the toilet bowl



Replacing the toilet is able to transform any toilet. Of course, because the toilet is the central and integral part of any toilet, and therefore should look so that it was nice to sit down. So, you bought a new toilet. But you still need to install it. And to install a new one, you must first dismantle the old toilet bowl. This we now and will.





Replacing the toilet will change the face of the toilet








Instructions





1


Shut off the cold water and drain the drainBarrel. Unscrew the flexible connection from the tank, as well as from the water supply, because in its place a new one will arise. And in the case of metal piping, you need to cut out a part of the pipe, then from the water pipe side, disassemble the first screwed connection in order to get a screw on the nut of the flexible connector.





2


The next step is the dismantling of the fasteningToilet seat to the floor. If fastening is carried out by means of bolts - unscrew them, by means of cement - break it on possibility or a toilet bowl in places of its fastening to a floor. After you remove the fixation, tilt the toilet bowl back until it stops, so that the water left in the toilet bowl fuses to the end.





3


Then detach the bell. If it is corrugated, it is quite easy to remove it. But to disconnect the plastic or iron bell, you need to remove the toilet. The bell is disassembled as far as possible before the first connection. This is necessary to insert a drain flute. You can also cut the socket to fit the size.





4


Install the drain outletcorrugation. To do this, it must be greased with a sealant from the side of its entry into the sewer. Pre-clean and grease the sewer siphon itself. Now insert the corrugation into it until it stops. To the smell of sewerage in the toilet did not spread, cover the rag open entrance corrugation.





5


So the toilet is dismantled. When installing a new toilet, we consider two cases. In the first case, the floor remains flat, because the old toilet bowl was fixed to the floor with bolts. If the new toilet has a similar mount, try installing it in the old place. Drill out plastic plugs from the holes in the floor and replace them with new ones. If the old holes are wider than the new dowels, the toilet will be unreliable. You will have to drill new holes. Place the new assembled toilet bowl to the place where you intend to install it, then mark the floor for new holes, taking into account the dimensions of the toilet bowl, the length of the corrugation and the liner. Drill holes, insert dowels and secure the toilet seat in place.





6


If the toilet was cemented, there will be aDeepening. Clean this cavity of cement. In typical houses, usually under the cement is a wooden mortgage. In principle, you can level the floor with a thick solution, install the toilet on top and screw it to the wooden mortgage directly through a wet cementitious screed with screws. After the cement has dried, you will have to twist the screws. The truth is, there is one nuance: a mortgage can decay with time, so it should not be checked for durability in this way. It is better to make a screed, especially if the mortgage is not in principle. Screed can dry for up to three days depending on its constituents. After this time, she can safely hold the dowels.





7


Gently hammer the anchor plugs into the ready-made holes in the floor. They should enter neither hard nor easy. The stability of the toilet is largely dependent on this step.












Tip 3: Independent installation of a toilet bowl



If you make repairs yourself and have already reachedbefore buying plumbing, then for sure you are already faced with the problem of installing a toilet. In fact, installing a toilet bowl with your own hands is not so difficult as it might seem at first glance.





Independent installation of a toilet bowl







After buying a toilet it is necessaryneatly collect, while you need to act with caution. It is advisable to check for leaks after the assembly. In the presence of leaks, you need to use a variety of special seals.

Clamps are not recommended for excessive force, otherwise a crack may result.

After assembling it is necessary to install a toilet bowl and check whether it is convenient. This is necessary, so that later you do not fight your head on the shelves, or have access to communications located behind the toilet.

After the installation site is finalselected, it is necessary to mark the holes for fastening the toilet bowl. After that using a perforator and a drill of the corresponding diameter you need to make holes.

If the floor is tiled in the toilet, thenit is desirable to start the drilling in a non-impact mode at low speed, in order to avoid the appearance of cracks in the tile. When the holes in the floor are made in them, you can insert plastic dowels.

Repeatedly try on, the toilet and the contour, marking, then on the place where the toilet will stand, we apply a layer of sanitary silicone along the contour.

After applying the silicone, carefully install the toilet bowl and fix it with screws, while checking the toilet bowl for shakiness and do not allow too much clamping with screws.

Surplus silicone can be cleaned with a damp cloth. Then you can connect water to the drain tank, and the corrugation to the toilet, while you can also use special sealants.










Tip 4: How to mount a toilet bowl



Self-installation of a new Toilet bowl - a task, although difficult, but quite feasible for almost any home master. How to properly mount the toilet?





How to mount a toilet bowl








You will need




  • - punch;
  • - spanners;
  • - adjustable wrench;
  • - a hammer;
  • - silicone sealant;
  • - Screwdrivers;
  • - Bulgarian;
  • - a rag




Instructions





1


Close the cold water. Drain the water from the tank Toilet bowl And detach the piping. In the case of metal piping, it is necessary to saw off a part of the pipe with a grinder and to disassemble the threaded connections located on the water supply side, so that it becomes possible to fasten the nut of the flexible podvodki. If the old Toilet bowl flexible piping - just unscrew it from the tank and water.





2


Disconnect the toilet bowl from the floor. If the toilet is bolted, unscrew it. In the case of fixing on cement, it is necessary to break it or the old toilet itself, in the place of attachment, with the help of a hammer. Drain the remaining water by tilting the toilet bowl back.





3


Remove the socket by removing the old drain flute. If the socket is cast-iron or plastic, then it is necessary to disassemble it before the first connection or to cut down to the size of the new drain corrugation.





4


Thoroughly clean the socket and lubricate itsealant. Take a new corrugation, lubricate it with silicone and insert it into the socket as far as it will go. In order to avoid the spread of an unpleasant odor from the sewer pipes, cover the drain hole with a cloth.





5


Prepare the floorIf the old and new Toilet bowl The same mounting bolts, then you can installplumbing in the same place. Drill out old plastic dowels from the floor and replace them with new ones. Make sure that the dowels tightly enter the holes. If necessary, drill new holes, after noting their location. If the toilet was cemented, then it is necessary to make a cement screed. Wait until the cement slurry dries completely - this can take from 1 to 3 days. Make fixing holes in the floor and hammer in them plastic dowels.





6


Put a new toilet bowl on the installation site and tighten the fastening bolts.





7


Carefully seal the bell Toilet bowl silicone sealant and wear corrugation.





8


Connect the toilet to the water pipe using a flexible cable. To do this, screw one end of the line to the water pipe, drain a little water through it, and then fix the other end on the tank.





9


Turn on the water, wait until the tank is full and drain. Make sure there are no leaks. Your toilet bowl is installed.











Tip 5: How to install a toilet bowl



Nothing is eternal, and even that seemedWould, simple, plumbing equipment, like a toilet, fail. Starting the overhaul in the house or apartment, many are wondering how to properly install the toilet so that it can last as long as possible. This work requires a scrupulous approach, which does not tolerate negligence. Therefore, when there is the slightest doubt in their abilities, it is best to entrust the installation of equipment to specialists.





How to install a toilet bowl








You will need




  • - Drill;
  • - silicone mastic;
  • - The fan tube;
  • - Hex to "12";
  • - adjustable wrench;
  • - marker;
  • - drill bit for concrete;
  • - bolts;
  • - dowels.




Instructions





1


Before installing a new toilet, you needdetermine its location. This plumbing equipment differs from similar devices in that through it passes not only water, but also other more solid products of human life. Their entry into the sewer pipe is carried out through a branch to the toilet. To avoid the accumulation of waste in it, installation should be carried out near the sewer riser.





2


In some apartments the layout of the toilet is arrangedin such a way that it is impossible to install the toilet next to the riser. In this case, you need to provide a small bias, equal to two degrees, a tap for the toilet.





3


The toilet is installed on the floor or on a tile. Compensate the unevenness of the floor by gluing the sealant to the base of the sanitary equipment.





4


There are several ways to install the toilet. The first of these is carried out using a corrugated pipe. In this method, it is not necessary to take into account the position of the toilet bowl with respect to the sewer opening. This type of installation is recognized as the most simple and convenient, however, it has some drawbacks. The main disadvantage is the large size of the corrugation, which prevents plumbing close to the wall. The second disadvantage is that the place where the toilet and corrugation are combined is very soft and fragile. If the installation is not neatly done, it can easily be damaged, but it will not be possible to restore it.





5


The second way of installing the toilet is more difficult,But does not contain the drawbacks of the former. It is carried out with the help of sewage pipe bends. This allows you to get a more rigid and strong connection of the toilet bowl with sewerage. When installing plumbing in the second way, the main element is a branch pipe that connects the toilet and the sewage system. It can be of two types: straight and curved. If the outlet hole is placed horizontally, use a corner pipe. The value of the angle is determined depending on the location of the sewer pipe relative to the hole. A straight pipe is used in cases where the outlet is not horizontal.





6


Sometimes the toilet is located in parallelA sewer hole. In this case, an additional corner element of the pipe is required. The complexity of the second method of installing sanitary ware consists in the obligatory fitting of the optimal arrangement, in determining which the length and angle of inclination of the nozzle are taken into account. At the end of the docking, the toilet seat is finally fixed to the floor.